If you happen to’ve chosen the incorrect channel map in Betaflight, your drone will reply to the incorrect sticks, inflicting management points. It’s important to make sure the right channel map is chosen within the Receiver tab in Betaflight. If you happen to’re uninterested in altering the channel map every time you arrange a brand new drone, I may even present you how you can configure channel order in your EdgeTX radio so that you received’t want to alter it once more.
Searching for a brand new radio? Listed here are my really useful radio transmitters: https://oscarliang.com/radio-transmitter/#Radio-Suggestions
What’s Channel Map in Betaflight?
Channel mapping refers back to the order during which your radio’s controls (throttle, yaw, pitch, roll) are transmitted to your drone. Betaflight expects these controls in a particular order based mostly in your settings.
The 2 most typical channel map settings for FPV drones are:
- AETR (Aileron, Elevator, Throttle, Rudder)
- TAER (Throttle, Aileron, Elevator, Rudder)
Every letter represents a particular channel:
- A (Aileron) = Roll (left/proper)
- E (Elevator) = Pitch (ahead/backward)
- T (Throttle) = Throttle (pace up/down)
- R (Rudder) = Yaw (rotate left/proper)
In case your radio’s channel order doesn’t match Betaflight’s setting, your controls will change into blended up—for instance, throttle controlling roll or yaw controlling pitch.
Why is Channel Map Vital?
You could surprise why channel map is required. Nicely, a channel map defines the order of channel outputs (stick instructions). Nevertheless, when these outputs attain the receiver, they’re merely numbers. Your flight controller must be explicitly knowledgeable which quantity corresponds to every command (throttle, pitch, roll, yaw).
Choosing the incorrect channel map in Betaflight will lead to incorrect responses to your stick inputs. Your quad could refuse to arm as a consequence of throttle not being at zero, or if it arms, it might behave unpredictably and uncontrollably.
Default Channel Order in Betaflight
You may view or change the channel map in Betaflight Configurator beneath the “Receiver” tab, listed as “Channel Map”.
The default Betaflight channel order is AETR1234:
- CH1: Aileron (Roll)
- CH2: Elevator (Pitch)
- CH3: Throttle
- CH4: Rudder (Yaw)
The best way to Repair Mistaken Channel Map
In case your receiver channels are blended up, merely strive a distinct channel map possibility within the Receiver tab of Betaflight Configurator:
- Betaflight default: AETR (AETR1234)
- Various frequent possibility: TAER (listed as “Spektrum / Graupner / JR”)
If not one of the preset choices appropriate the problem, test your transmitter’s channel mixing configuration. Directions are supplied within the subsequent part.
Channel Order in EdgeTX Radio
You may view your radio’s channel order on the MIXES web page in any EdgeTX radio.
To keep away from altering Betaflight’s channel map each time you setup a brand new drone, I’d advise to set your radio’s default channel order to match Betaflight’s default (AETR). This entails putting:
- Aileron (Roll) on Channel 1
- Elevator (Pitch) on Channel 2
- Throttle on Channel 3
- Rudder (Yaw) on Channel 4
Additional Studying: Try this beginner-friendly tutorial on organising switches within the MIXES web page: https://oscarliang.com/setup-switch-mixes/
You may also wish to affirm/set the default Channel Order in EdgeTX – it ensures each new mannequin profile created in your EdgeTX radio will routinely use the specified channel order:
- Press the SYS button to entry radio settings.
- Navigate to the Settings tab.
- Scroll down and discover Default Channel Order.
- Set it to AETR.
- Press Return to save lots of your modifications.
The best way to Change Channel Order in EdgeTX
To rearrange channel order in your EdgeTX radio, navigate to the MIXES web page in Mannequin Setup, and reorder the primary 4 channels as wanted. For instance, to alter TAER to AETR:
Choose the channel you want to transfer, maintain the Enter button, and click on on “Transfer.”
Transfer THR to CH3 (simply above ELE).
Transfer AIL to CH1, and ELE to CH2.
Verify that the channel map in Betaflight is now appropriate.
Observe: The order of controls within the INPUTS tab doesn’t matter and might stay unchanged.
Conclusion
Setting your EdgeTX radio’s default channel order to match Betaflight’s (AETR) simplifies your setup course of considerably. With this adjustment, your drones will at all times reply appropriately to your controls, permitting you extra time flying and fewer time troubleshooting. Completely satisfied flying!
Edit Historical past
- 2020 – tutorial created
- Mar 2025 – tutorial up to date